Answer by Doug Smythies for How do I disable a specific CPU core at boot?

You can make use of CPU hotplug abilities to achieve your objective. You can boot CPUs 0-13 and then add the others (CPUs 15-27, and 29-31) afterwards.

All Xeon processors have hyper threading, so I assume you mean 16 cores at 2 threads per core, for a total of 32 CPUs. This answer is written, and tested, for a 4 core, 2 threads per core, processor, where core 2 is the bad one.

First, as sudo, edit /etc/default/grub and add the maximum boot time CPUs, maxcpus=, to your GRUB_CMDLINE_LINUX_DEFAULT line. Example for my system:

Was:

GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 consoleblank=300 cpuidle_sysfs_switch cpuidle.governor=teo"

Now:

GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 consoleblank=300 cpuidle_sysfs_switch cpuidle.governor=teo maxcpus=2"

Where I used maxcpus=2 you would use maxcpus=14.

Save a copy of grub first, and run sudo update-grub after.Thus, the system will boot only using cores 0 and 1, and in CPUs 0,1 being on-line:

doug@s15:~$ grep . /sys/devices/system/cpu/cpu*/online/sys/devices/system/cpu/cpu1/online:1/sys/devices/system/cpu/cpu2/online:0/sys/devices/system/cpu/cpu3/online:0/sys/devices/system/cpu/cpu4/online:0/sys/devices/system/cpu/cpu5/online:0/sys/devices/system/cpu/cpu6/online:0/sys/devices/system/cpu/cpu7/online:0

Note: For the default Ubuntu kernel configurations CPU 0 is always online, and there is no such thing as:

doug@s15:~$ grep . /sys/devices/system/cpu/cpu0/onlinegrep: /sys/devices/system/cpu/cpu0/online: No such file or directory

O.K. so now, bring the other desired cores and CPUs on-line:

doug@s15:~$ echo 1 | sudo tee /sys/devices/system/cpu/cpu3/online1doug@s15:~$ echo 1 | sudo tee /sys/devices/system/cpu/cpu4/online1doug@s15:~$ echo 1 | sudo tee /sys/devices/system/cpu/cpu5/online1doug@s15:~$ echo 1 | sudo tee /sys/devices/system/cpu/cpu7/online

And check:

doug@s15:~$ grep . /sys/devices/system/cpu/cpu*/online/sys/devices/system/cpu/cpu1/online:1/sys/devices/system/cpu/cpu2/online:0/sys/devices/system/cpu/cpu3/online:1/sys/devices/system/cpu/cpu4/online:1/sys/devices/system/cpu/cpu5/online:1/sys/devices/system/cpu/cpu6/online:0/sys/devices/system/cpu/cpu7/online:1

So now, I have cores 0,1,3 on-line and core 2 offline and 6 CPUs available.Note that core 0 = cpus 0 and 4, core 1 = cpus 1 and 5, ...

EDIT 1: For 32 CPUs, perhaps you have multiple nodes (processors), so the core to CPU mapping might be different.

EDIT 2: It may be that the CPUs that are brought on-line after boot default to using the performance governor in the intel_pstate CPU frequency scaling driver, which is the kernel configuration default (which gets changed to powersave 1 minute after boot, for the boot enabled CPUs). You might want to check and set all CPU governors to your preference, typically the powersave governor. To check do:

grep . /sys/devices/system/cpu/cpu*/cpufreq/scaling_drivergrep . /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor

To change governors do, for example (notice as root):

# for file in /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor; do echo "powersave"> $file; done

Once you have things working the way you want you can automate the additional on-line after boot step (see other questions and answers for "how to").

Note: It seems to me that you should be able to achieve your objective in one boot step via "cpu_possible_mask" manipulation via "possible_cpus=n", but I couldn't get it to work. Someone else might know.